iFlight Beast V2 F7 55A AIO

The Beast F7 55A AIO V2 FC (BMI270) is iFlight's new innovation! The new Beast series of AIO FCs combines MCU speed with ESC for a bigger stack! Features an onboard Barometer for possible long-range flights and much more! This lightweight AIO FC was designed to make room for flight firmware development like Betaflight, Emuflight, etc. iFlight used BGA chipsets instead of ordinary QFP (big size) MCUs and ultra-powerful Mosfets for almost any build. Solder your motor wires and you are good to go!

Features

• V1.2-V2: Circuit improvements have been implemented
• Vista digital system Plug-and-Play (VBAT passthrough)
• Compatible with digital and analog
• BGA-STM32F745, 216MHz MCU
• 16MB Onboard Flash Blackbox
• 5V 2.5A BEC output
• DPS310 Barometer
• AT7456E OSD
• BMI270 Gyro

Specifications

Beast F7 AIO FC

• FC Firmware：IFLIGHT_F745_AIO_V2
• Mounting pattern: 25.5*25.5mm φ3mm
• Blackbox: 16MB Onboard Flash
• OSD: iFlight OSD (AT745E)
• Dimensions: 32.5*32.5mm
• MCU: BGA-STM32F745
• Connector: Micro-USB
• BEC output: 5V 2.5A
• Barometer: DPS310
• Gyro: BMI270
• Weight: 8.5g

55A 2-6S ESC

• Mounting pattern: 25.5*25.5mm/Φ3mm
• Dimensions: 32.5*32.5mm
• ESC Firmware: G-H-30 BLS
• Constant: 55A / Burst: 60A
• Current Sensor: Yes
• Current scale: 100
• BLHeli: BLHeli-S
• Input: 2-6S LIPO
• Telemetry: no
• Uarts: 5

Safety Tips

The DJI plug&play port has no voltage regulator (BEC) and is passing through VBAT. The Caddx Vista goes up to 26.4V (6S), the DJI Air Unit goes up to 17.6V (4S). Make sure not to plug in your DJI Air Unit directly when you're flying 6S because this would fry it!

Small motor 4S builds should usually need an additional capacitor of at least 16V/220uF, for 6S go up to 35V or even 50V. Bigger motors have a bigger current draw, higher voltage spikes, and more serious back EMF (motor braking, works as a generator). Make sure to add big enough or even bigger low ESR capacitors on the AIO battery pad or on your battery lead the more aggressive motors you fly. There's a choice of capacitors in the package, but it's never a bad idea to make sure to protect your board. Smaller boards have less capacitance which has to be covered with external capacitors, there's no way around it.

Includes

• 1x 14AWG Silicone Cable Black 100mm
• 8x 0.8mm black Heat shrink tube 10mm
• 1x 14AWG Silicone Cable Red 100mm
• 1x XT30U 18AWG cable 70mm
• 1x XT60 16AWG cable 100mm
• 1x 1.0-7P cable 50mm-28mm
• 8x M2 Transparent Nylon Nut
• 1x Capacitor 470uF/16V
• 1x Capacitor 470uF/35V
• 4x M2 silicon grommets
• 1x 1.0-7P cable 50mm
• 8x M2*12mm screws
• 1x Beast F7 AIO