Happymodel Crux3 115mm 3" 1S-2S Caddx Ant BNF TBS Crossfire Nano

Multirotors → Racing FPV-Hubschrauber → RTF/ARF/PNF → 3" Quads → Happymodel Crux3 115mm 3" 1S-2S Caddx Ant BNF Frsky D8 SPI → Happymodel Crux3 115mm 3" 1S-2S Caddx Ant BNF TBS Crossfire Nano

Brand Name: Happymodel

Model: Crux3

Item Name: 115mm F4 OSD 1-2S 3 Inch Toothpick FPV Racing Drone

Wheelbase: 115mm

Size: 97x97x35mm (without propellers)

Optional Receiver Version:

Internal SPI Frsky version (Compatible with ACCST D8/D16, Recommend D8 mode)

Internal SPI Flysky version(Compatible with AFHDS and AFHDS-2A Flysky transmitter)

Internal SPI DSM2/DSMX version(Compatible with Spektrum or Multiprotocol DSM2/X radio)

External Frsky RXSR receiver version(ACCST D16 sbus output)

External TBS Crossfire Nano receiver version

Weight: 41g (without battery)

Recommend Lipo Battery: 2s 350mah/400mah/450mah/520mah Battery ( NOT Included)

EX1202.5 6400KV Motor	Configu-ration:9N12P Stator Diamter:12mm Stator Length:2.5mm Shaft Diameter:Φ1.5mm Motor Dimension(Dia.Len):Φ1414.5mm Weight: 4.4g No.of Cells(Lipo):1-2S
Gemfan 3018 2-Blade Propeller	Center Thickness:5.5mm Prop Diameter:76.5mm Center Hole diameter:1.5mm
CrazybeeX FR V2.2 F4 Flight Controller	MCU: STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU6000 (SPI connection) Board Size: 28.5x28.5mm Power Supply: 1-2S battery input (DC 2.9V-8.7V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Betaflight OSD(SPI Control) Built-in 5.8G VTX Built-in SPI Frsky/Flysky receiver or no receiver Built-in 5V 1A BEC (Frsky SPI RX Version) CRAZYBEEX FR V2.2 FC Firmware target: CrazybeeF4FR (Flysky SPI RX Version) CRAZYBEEX FS V2.2 FC Firmware target: CrazybeeF4FS (DSM2/X SPI RX Version)CRAZYBEEX DXS V1.0 FC firmware target: CrazybeeF4DXS (External Frsky RXSR Version) CRAZYBEEX PNP V2.2 Firmware target: CrazybeeF4DX (External TBS CRSF NANO Version) CRAZYBEEX PNP V2.2 Firmware target: CrazybeeF4DX
Onboard 5A BL_S 4in1 ESC	MCU upgraded to EFM8BB21 Power supply: 1S LiPo/LiPo HV Current: 5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: S_H_50_REV16_7.HEX Default protocol: DSHOT600
Onboard Frsky SPI D8 Receiver Version	SPI BUS receiver Frsky D8 compatible Compatible Non EU transmitter D8 model Channels: 8ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m
Onboard Flysky SPI receiver Version	Protocol: AFHDS and AFHDS-2A Switchable Channels: 8ch(AFHDS) or 14ch(AFHDS-2A) No ground interference ( Transmitter and receiver 1 m from the ground): 200~300m Failsafe support
Onboard DSM2/X SPI receiver Version	SPI BUS receiver DSM2/DSMX compatible Channels: Max 12ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m RSSI enable (show on the goggles)
External Frsky R-XSR receiver version	Weight: 1.5g Number of channels: 16CH (1-16CH from SBUS channel, 1~8CH from CPPM channel) Operating Voltage Range: 3.5V~10V Operating Current:70mA@5V Firmware Upgradable Compatibility: FrSky X Series modules and radios in D16 mode Could support Frsky New ACCESS Protocol ( Upgrade firmware)
External TBS CRSF Nano receiver version	Original TBS CROSSFIRE Receiver ,CRSF Protocol , Official TBS transmitter compatible
Onboard 5.8G 40CH 25/200mW VTX	Output power: 25mw~200mw switchable Frequency: 40CH Input voltage: 3.3V 5.5V Current consumption: 300mA(type) Frequency: 5.8GHz 5bands 40 channels With Race band Smartaudio ready
Caddx ANT 1200TVL Camera	Image Sensor: 1/3" CMOS Sensor Horizontal Resolution: 1200 TVL TV System: NTSC or PAL Switchable IMAGE: 4:3 Synchronization: Internal Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000 S/N Ratio : >52dB (AGC OFF) Video Output: CVBS Lens: 1.8mm Min. Illumination: [email protected] Auto Gain Control: YES BLC: YES WDR: Global WDR DNR: 3D DNR Dimensions: 1414mm(with bracket to 1919mm) Wide Power Input: DC 3.7-18V Work Temperature: -20℃~+60℃ Weight: 2g (N.W.)

Features:

- 41gram 1-2s brushless Toothpick drone

- New AIO 4in1 CrazybeeX flight controller

- CADDX ANT 1200tvl Camera

- New 1202.5 brushless motor

- XT30 connector

- Compatible with Insta360 Go Camera ( this camera is NOT Included, you can add it by yourself.)

Pacakge Included:

1x Crux3 Frame and Canopy

1x Optional Receiver

1x F4 Flight Controller AIO 5A ESC Board

1x 5.8G 25-200mW VTX ( built-in Flight controller)

4x Happymodel EX1202.5 6400 KV Motor

4x Gemfan 3018 Propeller CW

4x Gemfan 3018 Propeller CCW

1x Caddx Ant 1200TVL Global WDR with OSD 2g Ultra Light Nano FPV Camera

1x Screw Driver

1x Propeller Disassemble Tool

1x Happymodel Handbag

41g Happymodel Crux3 115mm CrazybeeX FR V2.2 F4 AIO ESC 25/200mW VTX 1-2S 3 Inch Toothpick FPV Racing Drone BNF w/ 1202.5 Motor Caddx ANT 1200TVL Camera Support Insta360 Go

Preise für Happymodel Crux3 115mm 3" 1S-2S Caddx Ant BNF TBS Crossfire Nano in den Läden

Angebote gefunden: 23 (NewBeeDrone¹)

Store	Stock level	Lot price	Shipping cost	Coupon / promocode	Pcs./lot	1pc price
NewBeeDrone	Out of stock	$112			1	$112

Siehe auch

Happymodel Crux3 115mm 3" 1S-2S Caddx Ant BNF Frsky D8 SPI

$97

Join to our channels: new products, coupons, best deals: