Eachine US65 / DE65 PRO whoop comes with watertransfer craft and a New AIO 4 IN 1 CrazybeeX flight controller. The weight only 24g. High performance 2.0 plug design supporting up to 2S Lipo and 5A continuous current for each ESC. Caddx Ant 1200TVL Global WDR with OSD 2g Ultra Light Nano FPV Camera give you a highly view. Simply bind it to your transmitter then you are ready to enjoy your all-new Eachine US65 / DE65 PRO.

Manual and diff for US65 DE65 PRO, Click Here.

Specifications：

Brand Name: Eachine
Item Name: US65PRO DE65PRO

Wheelbase: 65mm
Size: 81mmx81mmx39mm
Weight: 24g(without battery)

Features:

24gram 1-2s brushless 65mm whoop

New AIO 4in1 CrazybeeX flight controller

Smooth and powerful

CADDX ANT Camera

High performance ET2.0 plug

Advantage compared to the PH2.0
★Solve the voltage sag problem
★15A continuous current, 20A burst
★1.0mm gilde banana connector decreased internal resistance

Receiver option:

Internal SPI Frsky version (Compatible with ACCST D8/D16, Recommend D8 mode)

Internal SPI Flysky version(Compatible with AFHDS and AFHDS-2A Flysky transmitter)

External Frsky RXSR receiver version(ACCST D16 sbus output)

External TBS Crossfire Nano receiver version

Flight controller	(Frsky SPI RX version) CRAZYBEEX FR V1.0 FC Firmware target: CrazybeeF4FR (Flysky SPI RX version) CRAZYBEEX FS V1.0 FC Firmware target: CrazybeeF4FS (External Frsky RXSR version) CRAZYBEEX PNP V1.0 Firmware target:CrazybeeF4DX (External TBS CRSF NANO version) CRAZYBEEX PNP V1.0 Firmware target:CrazybeeF4DX MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Board size: 28.5 * 28.5MM Power supply: 1-2S battery input (DC 2.9V-8.7V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Betaflight OSD(SPI Control) Built-in 5.8G VTX Built-in SPI Frsky/Flysky receiver or no receiver Built-in 5V 1A BEC Built-in voltage detection
Motor	Mode: NX0802 14000KV Configu-ration:9N12P Stator Diamter:8mm Stator Length:2mm Shaft Diameter:Φ1mm Motor Dimension(Dia.Len):Φ10.5mm14.9mm Weight(g):1.7g No.of Cells(Lipo):1-2S
Onboard 4in1 ESC	MCU upgraded to EFM8BB21 Power supply: 1-2S LiPo/LiPo HV Current: 5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: S_H_50_REV16_7.HE* Default protocol: DSHOT600
Propellers	Gemfan 1219-3 Center Thickness:5mm Prop Disk Diameter:31mm Center Hole Inner diameter:1.0mm
Onboard 5.8g VTX	Output power: 25mw Frequency: 40CH Input voltage: 3.3V 5.5V Current consumption: 300mA(type) Frequency: 5.8GHz 5bands 40 channels With Race band Smartaudio ready
Caddx ANT 1200tvl camera	Image Sensor: 1/3" CMOS Sensor Horizontal Resolution: 1200 TVL TV System: NTSC or PAL IMAGE: 16:9 or 4:3 Synchronization: Internal Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000 S/N Ratio : >52dB (AGC OFF) Video Output: CVBS Lens: 1.8mm Min. Illumination: [email protected] Auto Gain Control: YES BLC: YES WDR: Global WDR DNR: 3D DNR Dimensions: 1414mm(with bracket to 1919mm) Wide Power Input: DC 3.7-18V Work Temperature: -20℃~+60℃ Weight: 2g (N.W.)
Lipo Battery	Capacity:250mAh Voltage:3.8v Continuous Discharge Rate: 30C Size: 55mmx12mmx7mm Weight: 6.5g Connector: ET2.0
Multi port Lipo/Lihv battery charger	Weight: 41g Dimensions: 82x51x22mm Input: DC 7V-22V Output switchable: Fixed at 200~600 milliamps Cutoff voltage switchable: 4.20v cell charging cutoff (+- 0.5% margin of error) for 1S Lipo Battery 4.35v cell charging cutoff (+- 0.5% margin of error) for 1S 3.8V LIHV Battery
Onboard Frsky SPI receiver Version	Onboard Frsky SPI D8 receiver Version SPI BUS receiver Frsky D8 compatible Compatible Non EU transmitter D8 model Channels: 8ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m Onboard Flysky SPI receiver Version SPI BUS receiver Protocol: AFHDS and AFHDS-2A Switchable Channels: 8ch(AFHDS) or 14ch(AFHDS-2A) No ground interference ( Transmitter and receiver 1 m from the ground): 100~200m Failsafe support
External Frsky R-XSR receiver version	Weight: 1.5g Number of channels: 16CH (1-16CH from SBUS channel, 1~8CH from CPPM channel) Operating Voltage Range: 3.5V~10V Operating Current:70mA@5V Firmware Upgradable Compatibility: FrSky X Series modules and radios in D16 mode Could support Frsky New ACCESS Protocol ( Upgrade firmware)
External TBS CRSF Nano receiver version	Original TBS CROSSFIRE Receiver ,CRSF Protocol , Official TBS transmitter compatible