Happymodel Snapper7 75mm Crazybee F3 OSD 5A BL_S ESC 1S Brushless Whoop FPV Racing Drone BNF

Notice: FrSky LBT EU Firmware D16 Transmitter can not compatible with FrSky version drone.
You can change your transmitter to LBT EU Firmware D8 version or International version.

Specification: ( DSMX/ DSM2 Version Manual )
Brand Name: Happymodel
Model: Snapper7
Item Name: 75mm Wheelbase 1S Brushless Whoop FPV Racing Drone
Wheelbase: 75mm
Version: Basic Version / Standard Version ( Optional)
- The diffirence of them are the package lipo battery and charger
Receiver: Compatible Frsky D8 Receiver OR
Compatible Flysky AFHDS/ AFHDS-2A Receiver ( Optional)

Size: 98.5mm*98.5mm*36mm

Weight: 28g (without battery)
Take off weight: 41.8g (with battery)

Crazybee F3 Flight Controller	Item Name: Crazybee F3 FC MCU: STM32F303CCT6 (72MHZ, 256K FLASH) Sensor: MPU-6000 (SPI connection) Power supply: 1S battery input (DC 3.5-4.35V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Frsky receiver Or Flysky Receiver Built-in Betaflight OSD(SPI Controll) Built-in Current meter (Max 14A,could be modified to 28A by replace resistor) Built-in 5V 0.8A BEC with LC filter Built-in voltage detection BLHELI_S pass-through Ready Firmware: Betaflight_3.3.0_Crazybee Board size: 28.5 * 28.5MM Board weight: 3.5 g Heading LED Ready
Onboard 5A 4 In 1 ESC	Power supply: 1S LiPo/LiPo HV (4.2v/4.35v) Current: 5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: O_L_5_REV16_6.HEX Motor connector: JST PH1.25 3pin Signal Support: Dshot150/Dshot300/Dshot600/Oneshot125/Multishot/PWM
Onboard Frsky Receiver Version ( Optional)	SPI BUS receiver Frsky D8 Compatible both of Non EU and EU LBT transmitter Channels: 8CH Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground) : 300m
Onboaed Flysky Receiver Version ( Optional)	SPI BUS receiver Protocol: AFHDS and AFHDS-2A Switchable Channels: 8ch (AFHDS) or 14ch (AFHDS-2A) No ground interference (Transmitter and receiver 1 m from the ground): 300m Failsafe support
0802 19000KV Motor	Model: 0802 KV: 19000KV Configu-ration: 9N12P Stator Diamter: 7mm Stator Length: 3mm Shaft Diameter: Φ1.0 Motor Dimension (Dia.Len) : Φ1014.5 Weight: 2.5g No.of Cells: 1S Lipo
Propeller	40mm 3-blade Propeller ( 4 CW + 4 CCW)
5.8G VTX AIO Camera	5.8G 48CH 25mW VTX Output Power: 25mW Frequency: 48CH With Raceband: 5474-5945 MHZ Input Voltage: 3.3V-5.5V Current Consumption: 300mA (type) 700TVL Camera Camera Resolution: 700TVL Field of View: 120° Video Format: NTSC Antenna: RG178 antenna Size: 13.9x12.0mm( LxW) Weight: 3g
3.8V 450mAh Lipo Battery	Capacity: 450mAh Voltage: 3.8V Continuous Discharge Rate: 30C Instantaneous Discharge Rate: 60C Size: 60x18x7mm Weight: 13.6g Connector: PH2.0

Features:

- Betaflight support, multi flight mode: ACRO/AIR/ANGLE

- Powerful Brushless motor and Smooth ESC

- CNC aluminum alloy propeller guard

- Betaflight OSD support, easy to get RSSI, Voltage and other info from your goggles

- Adjust the settings and the PID of the flight controller via OSD

- Frsky version support both EU LBT and NON-EU Frsky transmitter

- Full telemetry function ready

- Head lights ready

- Camera angle adjustable

- Real Bind and Fly version

Package Inlcuded:
Basic Version
1x Snapper7 75mm FPV Drone
4x 40mm 3-Blade Propellers ( 4 CW & 4 CCW)
1x 3.8v 450mah 30C/60C Lipo battery
1x USB Lipo/LIHV Charger
1x Propeller Disassemble Tool
1x Screwdriver

Standard Version
1x Snapper7 75mm FPV Drone
4x 40mm 3-Blade Propellers ( 4 CW & 4 CCW)
3x 3.8v 450mah 30C/60C Lipo Battery
1x 1S06 6 Way Lipo/LIHV charger
1x Propeller Disassemble Tool
1x Screwdrive